Cheek Riser with Overhang for CAR15 Stock | Multiple Versions Available

Cheek Risers for other stocks and braces can be found here

- Get Your LARP On: Inspired by the cheek risers used by high-speed guys in the 80’s and 90’s. The paper and steel targets at the range will appreciate your range-day drip.

- Multiple Versions:

• Apache: Has side indents on outside of riser. Has ridges on inside for friction-fit onto stock. Charging handle works with stock in 4th, 5th, or 6th position.
  • Longer "L" version is .3" longer front to back to be more clone accurate, works with stock in last two positions.
  • "XL" version is .3" longer than the "L" version, works with stock in last position only.
  • With Logo: Has Hammy3DPrints logo on left side, and "CAR 15" on right side.

• Comanche: Has side indents on outside of riser. Has raised circular portions on outside left side near rear of riser with Hammy3DPrints Logo and on the right side has "CAR 15". Has ridges like the Apache to clamp onto stock. Charging handle works with stock in 4th, 5th, or 6th position.
  • Longer "L" version is .3" longer front to back to be more clone accurate, works with stock in last two positions.
  • Is thinner at the top than the Apache, and has a longer slope on the sides - you can see the crease where the slope stops is further down on the Comanche

• Navajo: No side indents. Has flat internal faces (no ridges) to clamp onto stock. Charging handle works with stock in 4th, 5th, or 6th position
  
  • Longer "L" version is .3" longer front to back to be more clone accurate, works with stock in last two positions.
  • "XL" version is .3" longer than the "L" version, works with stock in last position only.

• Legacy: The first one I made, seen in the pictures labeled as Style 1 (Original). Stock must be at first position or further for charging handle to work.
  • Longer is same as Original but .75" longer in the front for more room for your cheek. Stock must be at second position or further for charging handle to work.

- Color and Stock Options: Available in Black, Earth Brown, and Forest Green. The Standard version will fit on standard CAR 15 stocks, including the B5 one and metal ones (except for Doublestar) I've tested with. The Brace version will fit on the H&R/PSA Brace. Neither version will fit the BKF or Olympic Arms stocks. NOTE: Neither version will fit the BKF, Bushmaster XM-15, or Olympic Arms CAR 15 style stocks.

- Battery Storage: The Apache, Comanche, and Navajo include a storage tube in the stock. They fit two (2) CR123/A batteries and come with a sleeve to snugly fit them. The cap applies light pressure to the batteries to hold them in place. If there is any rattling, tighten the rear cap. The diameter is also such that it will snugly fit 18650 batteries. As 18650 batteries differ in length depending on the specific model, and if they're protected or unprotected versions, you will need to fill in the extra depth with something pliable. I

- Secure Fit: Notched rear slides over the raised portion of the CAR 15 stock. The cylindrical nub inside the riser then fits into the circular hole on the top of the stock. This dual interface system ensures a tight fit without forward to rear movement. It may take some force to get the circular nub to fit into the hole on the top of the stock. It should not require any tools, just some muscle. 

- Sight Compatibility: The height of these risers will make the iron sights unusable. They are intended for use with an optic on top of a carry handle.

- Original Design: 2200+ products designed and 3D printed in the heart of America in St Louis, Missouri by Hammy3DPrints.

- Installation: Install the rear cap hand tight, such that the handle on the cap is horizontal, so it doesn't get in the way of the stock. Slide the rear of the riser down and onto the stock first. Then, slide it back until there is a 1/4" or so gap between the back of the cap and the raised portion of the stock, ensuring that the raised portion of the stock goes into the notch on the back. Then, push the front of the riser down firmly. If the riser is not seated, continue pushing back on the riser until the circular nub seats into the hole on the top of the stock.

MATERIAL: 3D printed using PETG-CF filament.

WARRANTY: If this item breaks I will make any design adjustments, if needed, and send a replacement for free.

Made in USA.

Please note that the products may have slight imperfections as 3D Printing is rarely perfect. The exact product you receive may also slightly vary from the product photos as I iterate and improve upon designs based on user feedback.